Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
features:aircraft [2020/03/24 18:11] Andreas Breitschopp |
features:aircraft [2023/01/17 10:41] (current) Andreas Breitschopp |
||
|---|---|---|---|
| Line 74: | Line 74: | ||
| You see the current load and voltage of all electrical bus system, see if the battery is currently charging or not and can trigger the APU or external/ground power if needed. | You see the current load and voltage of all electrical bus system, see if the battery is currently charging or not and can trigger the APU or external/ground power if needed. | ||
| - | :i: Note: Some options are only available if ProSim, AST or JeeHell is connected. | + | :i: Note: Some options are only available with certain third party aircraft options enabled. |
| ==== Pressurization System ==== | ==== Pressurization System ==== | ||
| Line 89: | Line 89: | ||
| Here you can open and close again the exit doors of your aircraft. | Here you can open and close again the exit doors of your aircraft. | ||
| + | |||
| + | ==== Glider Towing ==== | ||
| + | |||
| + | {{https://www.fs-flightcontrol.com/img/manual/features/aircraft/status-glider-towing.png?nolink|}} | ||
| + | |||
| + | Control glider towing and release in this section. | ||
| + | |||
| + | :i: Note: The winch option is only available with X-Plane. | ||
| ===== Engines ===== | ===== Engines ===== | ||
| Line 112: | Line 120: | ||
| There are quick access buttons for 0 %, 25 %, 75 % and 100 %, but you can also enter any specific percentage you want. Also reverse trust can be enabled for a specific or all engines by clicking on the button ''Reverse Trust'' if the engine supports that. | There are quick access buttons for 0 %, 25 %, 75 % and 100 %, but you can also enter any specific percentage you want. Also reverse trust can be enabled for a specific or all engines by clicking on the button ''Reverse Trust'' if the engine supports that. | ||
| - | :i: Note: The engine quick start options are only available if ProSim is connected. | + | :i: Note: The engine quick start options are only available with certain third party aircraft options enabled. |
| ==== Engine Switches ==== | ==== Engine Switches ==== | ||
| Line 172: | Line 180: | ||
| You can also define a relative altitude (by default it is generated exactly at the altitude your aircraft is currently at) and a vertical speed. | You can also define a relative altitude (by default it is generated exactly at the altitude your aircraft is currently at) and a vertical speed. | ||
| - | Finally trigger the aircraft generation with the button ''Generate TCAS Aircraft'' and remove all previously generated aircraft with the button ''Remove all TCAS Aircraft'' again. | + | Finally trigger the aircraft generation with the button ''Generate Intruder Aircraft'' and remove all previously generated aircraft with the button ''Remove all Intruder Aircraft'' again. |
| + | |||
| + | :i: Note: The intruder aircraft type and vertical speed cannot be set if X-Plane is used. Also only one intruder at the same time is supported for X-Plane. | ||
| ===== ATC Control ===== | ===== ATC Control ===== | ||
| Line 181: | Line 191: | ||
| :i: Note: If X-Plane is used you can only show or hide the ATC window here. | :i: Note: If X-Plane is used you can only show or hide the ATC window here. | ||
| + | |||
| + | ===== Change Aircraft ===== | ||
| + | |||
| + | {{https://www.fs-flightcontrol.com/img/manual/features/aircraft/change.png?nolink|}} | ||
| + | |||
| + | To change your aircraft in the simulator first select the new aircraft from the list and then click on the button ''Change Aircraft''. | ||
| + | |||
| + | With a commercial license you can restrict the aircraft available for selection in this dialog in the [[features:settings#change_aircraft|Settings]] module or disable this function altogether. | ||
| + | |||
| + | :i: Note: The simulator does not provide a preview image for all aircraft. | ||
| ===== Custom Buttons ===== | ===== Custom Buttons ===== | ||